Can you select multiple steps at once? Or just 1 at a time?
Thanks BTW!
Can you select multiple steps at once? Or just 1 at a time?
Thanks BTW!
You can select multiple steps. The delay value will either be on or off for every step; youâre given a visual representation of all 16 steps on the screen, and you toggle all the steps on or off. Itâs really fast and intuitive imo.
Just want to clarify that this function shouldnât be confused with something like Elektronâs micro-timing because you canât choose different values of delay for each individual step. Only one value can be chosen that can be applied to whatever steps you want it applied to.
If I recall correctly, this is similar to how the swing function worked on the old-school Korg Electribe EMX/ESXâs.
Cool - so itâs essentially swing, you just have to tell it what steps you want it on.
Iâm going to check this out at a store near me today.
picked one of these up from the classifieds here. pretty bitchinâ little box. still getting my head around the OS but itâs been a lotta fun so far. itâs very easy to push it and make it sound abrasive; it doesnât do âgentle and prettyâ as easily as the SH101, but itâs in there, as well as much more the SH101 canât do of course. the OS is pretty solid. my only gripe is that for some reason the sequencer wonât start when my Elektron boxes send it a start message; but if Ableton does, itâs fine.
also, to further expand on what Prints said above (and actually explain better than the manual does). in that editing mode, you set the Gate Delay (or length, etc) value youâd like, and then press whatever steps you want to apply that to. not ONE step, as the manual states; but one OR many. so, swing is easy to do.
I checked it out at lunch. I donât know if itâs for me. The delay sounds awesome though.
I had to leave just after I got it so havenât gone deep with it yet. Like another poster the midi was tricky but I need more time with it.
The Manther has a major competitor in the ARmk2 now that it has the dual VCO featureâŚ
This is not correct.
Actually you can set a different delay amount for each step. The workflow is: first rotate the encoder to choose the delay amount, then click the step or steps to apply that amount to. You can continue and dial in new values and apply them to other steps. Every step can be different if you want.
I only had the Manther for a bit, but I wasnât able to do what youâre describing. Thatâs great if you actually can.
Its not something I have done a lot either, so I did a double-check before I posted. You can set delay the same way as gate, accent, repeat and probability and can specify each of these per-step.
Hey i just picked one of these up. I do have a question though has anyone used mather with midi ? I cant seem to get it to take clock even with the clock settings set to midi. It dosnt take midi start or stop. I know my midi cable is active since ive tested on other devices.
Any one have this problem ?
can you use manther as source , not slave.
hey thanks for the reply. I havenât tested that it would require a bunch of rewire ect so i was avoiding that set up but good idea to test it. An if it dosnt work id say the midi is busted or it needs a up date ??
I had the same problem slaving it to a few devices. Had to leave for work before I had a chance to really investigate, but I will say I had a good solid system with a few different units and the manther messed things up. Not home for a few weeks so canât comment fully.
Iâm using midi clock from bitwig over usb and it is working correctly. Starts, stops and plays in sync.
ok figured out what it is so when you do a change with the clock you need to turn off then back on for the changes to take effect. so give that a try perhaps
I read on muffwiggler theyâre working on a firmware update , more envelope and lfo options, a few other things .
No date thoughâŚ
yeah I mentioned in my post just above you that Iâm having the same issue. I can send it start/stop messages and midi clock from Ableton and Logic and it behaves correctly. but in a computer-less setup, getting the clock from the OT (or RYTM; Iâve tried both), it syncs but doesnât start/stop correctly. Iâve tried various settings in both boxes but nothing has fixed the issue. Iâve definitely power cycled the Manther during this time too, with no changes.
hoping an OS update fixes itâŚ
Yea it defiantly seems buggy. I messed with it for a while but a reset was correcting the issues.