On the MICRO TIMING menu, there is a parameter called TRIG CONDITION with which a set of conditional rules can be applied to sample/note trigs, lock trigs, trigless trigs, and one shot trigs, using a parameter lock.
So no conditional locks for slide trigs and also none for recording or swing trigs.
Apparently slides are active with the subsequent sample trig, trigless trig, one shot trig, but not trigless lock trig.
Armed, not armed, TRC true or not, donāt seem to change slices behavior.
There is a thread for āhappy with update 1.31 people onlyā apparently.
Assuming these are RBG leds on both OTs: any other colour than slightly brighter red. I can almost never tell which is the active page without tapping page a couple of times
I know these LEDs are capable of lighting green. in the delay control mode they light green to indicate triplets & even divisions - but you canāt use this mode in GRID REC mode. Is there any conflicts with grid recording and other modes that use a green LED?
They have to be RGBā¦ Red obviously because they toast my eyeballs everyday, green happens on the startup animation, and green is a mix of yellow and blue. Yellow + red indicates the current page while the pattern is playing, which leaves blue as the only one we never really see directlyā¦
Darn the OT has so many features itās hard to keep track of some of the shortcuts. Surely thereās one trig shortcut that hasnt been taken yet?
Shame it seems to either sacrifice the crossfader or introduce a noticable amount of latency.
Either way Iām not really holding out for a big update. Just figured Iād share some of the things I wish the OT did better as itās a bit cumbersome in grid recording mode compared to newer devices. I suppose the best workflow for it is to record in live recording mode, using the trig buttons in chromatic or slice mode. Then going into grid recording to do clean-up.
The OT is almost perfect so i only want these 3 things:
Slider for MIDI please. I want to map CC parameters to scenes (A/B) just like all the other parameters. Please. Did i say Please? It makes no sense to hold the machine back like that. If you are concerned about MIDI resources i am okay with sacrificing LFOs in exchange or accept a limit of just 2 parameters per track or maybe even just one. (yes, i am that desperate)
Fix/Enhance the Bank Selection message. Give us an option for the alternative BSEL message. There is even room on the MIDI Setup Screen as only the top 3 knobs are occupied. There are many instruments out there that donāt work with the default Bank message (Behringer Deepmind, Roland JV or Novation Peak for example).
Inherit the intuitive multi-step editing from Digitakt and Digitone to the MK2. Allow us to edit multiple steps at once by just holding down as many trigs as humanly possible and apply the knob value to all of them. This makes programming a lot more creative and fun and is a huge workflow accelerator.
If you are really that desperate for that functionality I wouldnāt rely on a possible update, which in the case of the OT may never come (for various reasons).
You can always transform the outgoing CC48 (crossfader position) with some external midi processing to whatever you want. Transform it to dozens of other CCs on various channels and see if the MIDI cable starts glowing
I heard rumors that Elektron omitted it cause they were worried about MIDI bandwidth. I say thatās a hoax. If I can potentially send 8 x 3 fast cc LFOs over the wire I am sure having another value goin from A to B will not break it.
I looked into 2 midi dongles for the slider CC but I am not fond of having to manage the configurations for every bank externally. Might be different if that device would listen to program changes so I can sync settings to my current bank/part, but such device doesnāt exist as far as I know.
Elektron should just get on with it. There is no point holding backā¦ I am tired of handholding. Should just enable it and let us figure out the cons and find our own workarounds if there really is a bandwidth issueā¦
Iād also like a simple way to set RLen to number of steps beyond 64, it would make recording samples to be used as static files for easy slicing much simpler, without the use of needless workarounds.