I would open a support ticket. Also, I think the fact that the error occurred after loading samples is mere coincidence. Goldbaby is not to blame.
ok thanks
hehe yeah of course not re: goldbaby!
i do find it odd though that within 24 hours of deciding to add samples to the machine after not having time to get to it, this happens
Just heard back from support -
āWeāve seen a few reports of this error message, but when weāve investigated those units no faults have been found. If the pads work as expected thereās no need to worry. Please report back if you suspect that something isnāt working as it should and weāll investigate further.ā
In my ticket I asked for an explanation of what the error is, which I didnāt get - and Iām dubious that there are just a few reports of this message. But mostly Iām just concerned about a brand new synthesizer being doomed to recurrent issues.
Has anyone experienced the āmissing cal: padsā popup and then had zero issues moving forward?
I experienced the Missing Cal: Pads error message once, and have had zero issues moving forward. However, I experienced the problem while using the Rytm as an audio interface, which I stopped doing.
thanks, this is somewhat heartening
I got the rytm mkii 10 days ago. Since today it asks me to calibrate the pads. Unfortunately the manual does not mention this (only calibration of oscillators and filters is contained). Does anyone know how to trigger pad calibration?
Yes, I have exactly the same issue, the AR2 complains, but as far as I tried the pads seem to work.
I just had this Missing Cal: Pads error today, I restarted and everything seems to be ok, I also did test mode and got no errors, still, a bit disconcerting to see it on a brand new machine, running the latest OS 1.50.A
I see this once in a while at launch, starting again always remedied the blip
Same here, brand new machine, 1st startup sometimes with black screen, other times with missing cal pads error. Second startup solves the problem, a bit frustrating though
Exactly the same issue here with AR MKII brand new unit May 2020. Restart or after press any button resolves problem with āNOā key pressed too. Any ideas before sending this back to factory?
I too have just had the āMISSING CAL: PADSā error on the new AR Mk2 Black w/ firmware 1.60A, unit had been switched off overnight and when turned on it sat a little longer on a blank screen before showing the version and boot logo etc.
I restarted the device and it booted like normal but pads CH and MT looked like they had been triggered and the LEDs were fading out. It is currently still switched on and seems to be working as it should.
My unit is a little over a week old, it came with 1.60 pre-installed and so far have had no issues. I updated to 1.60A on the day it was released using the latest Elektron Transfer app on Windows.
Hi, Iāve had the exact same issue as you on my brand new Rytm MKII, CH and MT LEDs also fade out every time I boot the machine. Have you had any issues with the pads since this happened ?
no mate, no issues at all with the pads that iāve noticed
i have also not seen a repeat of the error message since i posted about it, but the pads glitch is there on every startup still
Well that is good news !
I just had this happen - brand new Rytm mk2 Black - I updated to latest firmware day it arrived.
I turned it on this morning and all the lights briefly flashed then nothing happened.
I waited and waited and still nothing (probs about 30 seconds). I then tapped a pad and the device began to start up, but once it finished booting I got the āMissing Cal: Padsā message appearing.
I have tried restarting and it happens like this every single time nowā¦
EDIT:
Okay wierd - I donāt know if related but I just tried this
- turned it off
- tap a pad (while itās still off!)
- turn it on
Now it seems to be fine?
Is there some kind of capacitor that isnāt being discharged properly or something and requires a pad to be pressed lol??
Now I seem to be able to turn it on properly without ever tapping pad again.
Strangeā¦
EDIT2:
Spoke too soon. Itās happening again lol
Mine does it occasionally, I just switch it off and back on without pressing pads
and it works fineā¦ had it for over a year and still works fine, I wouldnāt stress
Sadly my issues seem to have gone further- could be unrelated but its weird that today is the first time Iāve had this pad issue and now I see this:
Hi all,
I got the error once but just clicked it away and never looked back. I had no hardware issues during that lengthy session. Sometimes the unit freezes, but so does my DN. I suppose itās more of a software defect . Not planning on sending it in.
Cheers
Well all this has put me off buying one.