I want the Keystep to trigger both units to play and stop as well as send Midi notes to the Digitone. But I’m losing the sync from the Digitakt when using the Thru port. In this setup the Keystep sends out the clock and I need to dial in the right BPM which is very uncomfortable. The Digitakt should act as the master clock for everything else.
Someone said in another post to use a Midi Merger for this kind of purposes but I’m still unsure how to connect it right.
Of course you loose the sync from the digitakt, because MIDI thru just mirrors what’s coming in to MIDI in.
In your setup you need to combine Digitakt Thru and Digitakt Out into a single MIDI signal. That’s what a MIDI merger box does. It takes multiple inputs and generates a single output from them.
So:
Digitakt Thru -> Merger Box In1
Digitakt Out -> Merger Box In2
Merger Box Out -> Digitone In
Can’t this be solved with firmware by allowing a midi merge feature? The strymon effects boxes have the ability to change the Midi Out port to Out/Thru/Merge.
I’m experiencing this same issue trying to merge digitakt data with my iPad midi out data.
I think you can go:
Keystep out–>DT in, DT out–>DN in
Using the Keystep set to the autochannel of the DT, you can play the DN by having a a DT midi track selected and set to output to a corresponding channel of the DN…
Not sure if the transport from Keystep will work as you can’t separate the clock receive from transport receive on the DT and I’m not sure if you can on the Keystep. If the Keystep can send just transport then you can set the DT to receive only transport not clock, and set it to transmit both clock and transport…
If clock and transport are tied together on Keystep this might still work for you if your OK starting and stopping from the DT, just don’t set it to receive clock…
An option to explore anyway…
You should be able to use transport from teh keystep, if you enable receive transport and send transport in the midi settings. Also, obviously make sure you set the same for clock send/receive on both units. DT (send+receive) (DN receive)
This setup works surprisingly well! But I’m not able to use the transport from the Keystep and there’s no option in the Midi setting of the Digitakt to enable only transport. Just “Clock Send”, “Clock Receive”, “Prog Ch Send”, Prog Ch Receive".
Thanks Peter. I’ve got a midi cable going from Linnstrument out to Digitone In. The Linnstrument is set to channel 10 and the Digitone is set to channel 10 for auto channel. All that works great. Then I’ve got another mid cable going from Digitone Thru to Digitakt in. I’ve got the Digitakt set to auto channel 11 but nothing happens (even when I switch the Linnstrument to 11). If I set the Linnstrument to channel 9, 10, 12-16, I see a visual indication that the DT received a note. Nothing gets sent to the DT with the Linnstrument set to 1-8 (maybe because the DN is claiming those?)
For some reason the Digitone keyboard plays left to right through all the DTs tracks instead of different pitches in the selected track. I don’t care though cause the Linnstrument works great.
You may have transposed the Digitone’s trig-key-keyboard down to the lowest octave. If you transpose it up by one or more octaves, you should put the trig-key-keyboard into the note range to which the Digitakt responds chromatically.
What i have going on is Sledge > Digitakt IN > Digitakt OUT > Digitone IN
I wanted to be able to play the digitone from my midi controller with the common DT + DN setup. I wanted DT to send clock and pattern change + start and stop.
I have the DT tracks 1-8 set to off and tracks A-H set to 1-8.
on tracks 9-12 i set the midi channel on the SRC page to 1,2,3,4.
On Digitone i set track 1-4 to midi channel 1-4.
I also set mute destination on the DT to INT+EXT so i can use the DT for mute groups.
In order to play different tracks on the digitone i cycle through the corresponding midi track on my sledge and it works perfectly.
Hi rywal,
If I set mute destination on the DT to INT+EXT will be able to global mute and Pattern mute channels A to D?
I’m trying to do this, but only can global mute track channels on DN. How can I configure pattern mute on DT to mute DN track channels?? Plis some help.
Great video and it got me started but I need both units to start each other! For example when I press play on the DT it starts the DN with this set up but when I press play or rec and play on the DN to make a melody with the drums I’ve made on the DT the DT doesn’t start. Can it be done or do I have to keep unplugging both units and switching them? I can’t find any info on this?